Owens Corning Home Energy Audit in Boulder City: What to Know First
An Owens Corning home energy audit in Boulder City typically takes two to three hours on site, and you leave with before-and-after blower-door numbers, thermal imaging, and a written scope. Most audits run $350 to $650, and that fee is credited toward the work if you move forward. We’re an independent Owens Corning service provider, not affiliated with or authorized by the manufacturer.
This page is for Boulder City homeowners whose homes have Owens Corning insulation or envelope products and who want to know what’s actually happening inside the building envelope before they spend money on anything else. Our technicians have up to 10 years of experience, and every audit starts with a written price. Call (844) 320-7926 and a live person answers, day or night.
How Owens Corning Products Fail – and How We Fix Them
Owens Corning makes good products. The failures we find in Boulder City homes usually trace back to installation, not the material itself. Here’s what we see most often, and what it tells us.
- Atticat blown-in fiberglass settling below the marked depth. Owens Corning Atticat is loose-fill fiberglass that installers blow to a target R-value. Over time, and especially in Boulder City’s summer heat cycles where attic temps swing past 140°F, the material compacts and the actual R-value drops well below what the bag label promised. We measure depth at multiple points and compare against the original install target. The fix is usually topping off to the correct depth after air sealing, not a full removal.
- R-13 and R-15 kraft-faced batts with compressed or missing kraft. Owens Corning EcoTouch batts are common in Boulder City homes built between 2015 and 2025. When the kraft facing is torn, stapled poorly, or compressed into a bay that’s too narrow, the vapor retarder is compromised and the R-value falls. We check facing integrity at every joist bay and flag compression points the original crew may have missed.
- Owens Corning Foamular XPS at rim joists with gaps at the top plate. Foamular rigid board at the rim joist is a solid product, but it only works if it’s sealed at the perimeter. We routinely find Foamular panels butted tight to the subfloor with no sealant, leaving a continuous air channel behind them. That’s a blower-door leak you can measure. We seal the perimeter first, then reinstall or replace the board.
- Owens Corning R-19 and R-30 batts in crawl spaces with no vapor barrier beneath. Batts installed against a damp crawl space floor or without a ground cover absorb moisture and lose performance fast. In Boulder City’s dry climate this is less common than in wetter regions, but we still find it in homes near the wash corridors where soil moisture wicks up. We install a proper vapor barrier before any batt goes back in.
- Owens Corning duct wrap and duct board with failed seams. Owens Corning’s duct insulation products are reliable, but the seams and joints fail more often than the material. Leaky duct seams in a Boulder City attic can dump 20% to 30% of your conditioned air before it reaches a register. We run a duct leakage test and seal the seams before we touch the envelope.
One detail you won’t find on Owens Corning’s own site: Atticat’s blown density can vary noticeably between installers, and a bag that says R-49 on the label doesn’t guarantee R-49 in your attic. The only way to know is to measure depth at a dozen points and compare it to the attic card. We do that on every audit.
Our Owens Corning Home Energy Audit Process

- 1
Written price before anything starts. Under Haven Standard Clause 1, you get a flat price, a written scope, and a written warranty before anyone lifts a tool. No verbal estimates, no “we’ll see when we get up there.”
- 2
Blower-door test first. We pressurize the house to 50 pascals and record the CFM50 reading. That single number tells us how much air your envelope is losing. This is the baseline everything else is measured against.
- 3
Thermal imaging and insulation inspection. We walk the attic, walls, and rim joists with an infrared camera and check Owens Corning product depth, facing integrity, and coverage. You see the images as we take them.
- 4
Duct leakage test. We isolate the duct system and measure leakage separately from envelope leakage, so we know whether your problem is the shell or the ducts. Many Boulder City homes have both.
- 5
Written findings and a scoped repair plan. We tell you what we found, what it costs to fix, and in what order. If your Owens Corning batts are fine and the real problem is a top-plate leak, we say so. We don’t sell insulation you don’t need.
- 6
Post-work blower-door test and Documented Photo Record. After the work, we run the blower door again and show you the before-and-after numbers. You get photos of every step, included on every job.
What Owens Corning Home Energy Audit Costs in Boulder City
Here’s what Boulder City homeowners actually pay for the scenarios we see most often:
| Service | Typical Range |
|---|---|
| Full home energy audit (blower door, thermal imaging, insulation inspection, duct leakage test) | $350 – $650 |
| Blower-door test only | $150 – $275 |
| Duct leakage test only | $175 – $325 |
| Air sealing (top plates, can lights, penetrations) before insulation | $800 – $2,200 |
| Atticat top-off to correct depth | $1,200 – $3,000 |
| Rim joist Foamular reseal and reinstall | $400 – $900 |
What moves the price: attic square footage, how many penetration points need sealing, whether ducts are accessible, and whether your Owens Corning batts can be topped off or need removal. The audit fee is credited toward the work if you proceed. Every quote is a written price before any work starts, and a free second opinion on any written estimate is always available.
Why Boulder City Homeowners Call Envelope Insulation Boulder City for Owens Corning Work

We’ve sealed and insulated 9,000+ homes since 2016, and every one has a written price before work started and a documented record when the crew left. The 365-Day Done Right Promise backs every job: if it’s not done right, we make it right. On Owens Corning jobs specifically, our technicians check product depth, facing integrity, and installation quality – because we know the material is rarely the problem. The install is.
Calls are answered by a live person 24/7, technicians are background-checked and uniformed, and you get a text when they’re on the way. We also work with Reflectix and other brands, so if your envelope has a mix of products, we’re not going to tell you to rip out what’s working. We’ll read your competing quote with you, line by line, and tell you what we’d change. That’s the free second opinion, and it’s genuinely free.
FAQs
No. An audit is diagnostic. We inspect and measure your Owens Corning products without modifying them, so your manufacturer warranty stays intact. If we recommend repair work, we document existing product condition with photos before we touch anything, so there’s a record of what was there before we started.
Yes. We source from Owens Corning, Johns Manville, Knauf, Rockwool, CertainTeed, Icynene, Demilec, and GreenFiber, so we’re not locked into one brand. If your attic has Owens Corning Atticat and the right fix is to top it off with matching material, we do that. If a different product fits the application better, we’ll tell you why and let you decide.
Repair is almost always cheaper, and in most Boulder City homes it’s also the right call. Owens Corning batts that are intact but compressed can usually be fluffed and topped off. Foamular at the rim joist just needs proper sealing at the perimeter. Full removal and replacement is reserved for contaminated, wet, or pest-damaged insulation. We’ll tell you which category you’re in after the audit, with photos.
Most audits are scheduled within a few business days, and we answer the phone 24/7 so you’re not waiting on a callback. The audit itself takes two to three hours on site, and you get the written findings and scoped repair plan the same day.
The blower-door test measures how much air your home leaks at a standardized pressure, reported as CFM50. A lower number after work means a tighter envelope. For example, a Boulder City home that read 4,200 CFM50 before air sealing and 2,100 after cut its envelope leakage in half. That’s the number you paid for, and we publish it on every applicable job.
Call (844) 320-7926 for a free estimate on an Owens Corning home energy audit in Boulder City. Written price before any work starts, before-and-after blower-door numbers on the job, and the 365-Day Done Right Promise behind every visit.
Written by the team at Envelope Insulation Boulder City, serving Boulder City and nearby areas.