Trusted Blown-In Insulation for Boulder City Homeowners
If your Boulder City home feels hot by mid-morning and the upstairs never quite cools down, the attic floor is usually the first place to look. Blown-in insulation is the loose-fill material we blow across the attic floor to slow heat moving through the ceiling, and in this climate it earns its keep fast. Our technicians have up to 10 years of experience, and we don’t blow a single bag until the attic floor is air sealed. That order matters here, because Boulder City sits at roughly 2,500 feet in the Mojave, where summer attic temperatures push past 140°F. We answer the phone 24/7 and can often reach Boulder City the same day for an assessment. Call (844) 320-7926 and we’ll put a written price in front of you before anything starts.

What Our Blown-In Insulation Service Includes
Blown-In Cellulose
Cellulose is shredded recycled paper treated with fire retardant, blown wet or dry into attic bays and closed cavities. It’s a good fit for Boulder City homes chasing a high R-value on a tighter budget, and it settles into odd framing that batts can’t fill. We usually recommend it when the attic floor has irregular joist spacing or a lot of chases and wiring to work around. We source it from GreenFiber and install it to a measured depth, not a guessed one, so the R-value on your paperwork matches what’s actually in the attic. Cellulose also packs denser than fiberglass, which helps it hold against the desert’s afternoon winds that can find their way into a poorly detailed attic.
Blown-In Fiberglass
Fiberglass loose-fill is spun glass, and it’s the standard choice when you want an inert material that won’t settle as much over time. We reach for it in Boulder City attics where moisture control is already handled and the priority is a stable R-value that holds up through years of thermal cycling. Owens Corning and Johns Manville fiberglass both blow clean and predictable, and we’ve installed enough of both to know how each behaves at different depths. We choose fiberglass when the attic has a clear, dry path for the hose and the existing vapor profile is already right.
Dense-Pack Wall Insulation
Dense-pack is blown-in insulation installed tight into wall cavities at higher density, so it actually seals against air movement instead of just sitting in the stud bay. If you have an older Boulder City home built before wall insulation was standard, or a room that runs cold in January and hot in July, this is often the fix. We drill from the exterior or interior depending on siding and finish, pack each cavity to a measured density, and patch what we opened. It’s the one blown-in method that has to be installed carefully; under-dense and you’ve wasted the material, over-dense and you bow the drywall.
Blown-In Top-Up
Most Boulder City attics have some insulation already, just not enough of it. Blown-in top-up means we measure what’s there, air seal the floor, then add loose-fill on top until you hit the target depth. You need this if your current depth measures under about 10 inches, which we see in a lot of homes here that were built to older code minimums. We mark the final depth on every joist and hand you the photo record, so you can see the difference between “before” and “after” without crawling into the attic yourself. If your existing insulation is wet, compressed, or contaminated, we’ll talk about insulation removal and replacement before we top anything up.
Every one of these services starts with the same step: sealing the attic floor. We won’t blow insulation over an unsealed floor, because that traps the air leaks underneath and wastes the material. Under The Haven Standard, that’s a written scope before anyone lifts a tool.
Brands We Service for Blown-In Insulation

We work with materials from Owens Corning and Johns Manville because both are widely available and both blow to a predictable R-value when installed correctly. If a contractor has installed either product before, we already know where the depth typically gets skimped and how to check for it. We also install Knauf and Rockwool when the job calls for their specific material characteristics, and we’ll read a competing estimate that specifies any of these brands line by line with you if you bring one in.
If you’re not sure what’s already in your attic, we’ll identify it during the assessment. Whether your existing material is Owens Corning, Johns Manville, Knauf, Rockwool, or an older product that predates all of them, we can measure it, assess its condition, and make a recommendation that fits what’s actually there rather than pushing a replacement you don’t need.
Signs You Need Blown-In Insulation Right Now
- Your upstairs rooms run 5 to 8 degrees hotter than downstairs. That gap in a Boulder City summer usually points to a thin attic floor letting heat radiate down into the living space. It gets worse every year the insulation settles.
- You can see the tops of the ceiling joists when you look into the attic. If the wood is exposed, you’re likely under 6 inches of material, well below where Boulder City homes should be. Visible joists are one of the simplest signs, and one of the most reliable.
- Your HVAC runs almost constantly in July and August. A system that never shuts off is a system fighting an envelope it can’t win against. Insulation won’t fix a failing AC unit, but thin attic coverage is often the reason the unit can’t get ahead of the heat.
- You feel drafts near outlets, ceiling fixtures, or the attic hatch. These are air leaks, not just radiation, and they’re exactly what we seal before blowing any insulation. If we skipped that step, the new material would sit on top of the leak and change little.
- Your last energy bill jumped after a mild month. Rate changes happen, but a sudden, unexplained climb in the shoulder seasons often traces back to an envelope that’s lost performance. It’s worth one assessment before you assume it’s only the utility company.
Our Blown-In Insulation Process – Step by Step

We keep the sequence the same on every Boulder City job, and we do it in this order because the order is what makes the numbers move.
- 1
Written price and scope before we start. We walk the attic, measure existing depth, photograph what we find, and put a flat price and a written warranty in front of you before anyone touches a tool. Haven Standard Clause 1 is simple: have it in writing. You’ll know the number before we begin.
- 2
Air sealing, done first. We seal top plates, recessed can lights, plumbing and wiring penetrations, and the attic hatch. This is the step most contractors skip because it’s slow and invisible, and it’s the reason we won’t blow fiberglass or cellulose over an unsealed floor. If you’d rather see the full scope of what sealing covers, our home page lays out the envelope work.
- 3
Blower-door test before, and again after. A blower-door test is a pressurization reading that shows, in a single figure, how much air your envelope is losing, measured in CFM50. We take the “before” reading after sealing and before insulation so the improvement is real, not conflated with the material itself. Both numbers go on your documentation.
- 4
Blown-in installation to a measured depth. We install to a marked depth on the joists, not a rough guess, and we keep the hose path clear of can lights and chases. What we install depends on the material we recommended, and we’ll explain why we chose it for your attic.
- 5
Documented photo record and a walkthrough. We photograph the before, the sealing, the depth markers, and the finished attic, and hand you the record plus the blower-door readings. On the way out, we show you what changed. No mystery, no “trust me” finish.
How Much Does Blown-In Insulation Cost in Boulder City?
A typical blown-in top-up on a single-story Boulder City home with roughly 1,200 to 1,600 square feet of attic runs $1,500 to $2,800 including air sealing and both blower-door readings. If the attic has no insulation at all, expect $2,300 to $3,800 for a full installation to a proper desert R-value. Dense-pack wall insulation is priced by cavity and wall area, generally running $2.50 to $4.50 per square foot depending on how much drywall patching the job requires. Blown-in cellulose and fiberglass sit in similar ranges once you account for the depth each needs to hit the same R-value.
Four things move the number most: the square footage of attic floor, how much sealing work the top plates and penetrations need, whether old insulation has to be removed first, and how accessible the attic is. A home with a tight scuttle and a low roof pitch takes more labor than a walk-in attic. You avoid overpaying by getting the sealing and the readings priced in the same scope as the insulation, rather than as separate add-ons that quietly vanish from the estimate. A quote that doesn’t include air sealing isn’t a cheaper quote; it’s a smaller job.

Every estimate we give is a flat written price with the scope spelled out, and a free second opinion on any written estimate you already have. Bring us the competing quote and we’ll read it with you.
Blown-In Insulation Near Boulder City – Our Service Area

We reach Boulder City regularly, along with nearby Blown-In Insulation in Henderson and the surrounding communities toward Blown-In Insulation in Whitney. Most Boulder City visits can be scheduled within a day or two of your first call, and we answer the phone 24/7 so you’re not leaving a message in a queue. If your home sits out toward the lake or up in the hills, tell us when you call and we’ll confirm timing before we book.
Serving Boulder City, NV – Our Local Coverage Area
We serve Boulder City and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Blown-In Insulation in Boulder City

Blown-in insulation is loose material – cellulose, fiberglass, or a dense-packed blend – blown through a hose into an attic floor or wall cavity until it reaches a measured depth. In Boulder City attics it’s usually installed as a top-up over existing material or as a full fill on a new or bare attic. It’s fast to install, it fills irregular spaces better than batts, and it lets us hit a specific R-value without cutting and fitting rigid pieces around every joist and wire. The catch is that it only performs if the air leaks beneath it are sealed first.
A typical Boulder City attic top-up takes half a day to a full day, including air sealing and both blower-door readings. Dense-pack wall insulation usually adds a day depending on how many cavities and how much patching the walls need. A full install on a bare attic takes about a day for a home in the 1,200 to 1,600 square foot range. We’ll give you a real time window with the written price, not a vague “sometime next week.”
Most Boulder City top-ups fall between $1,500 and $2,800, and a full attic installation runs $2,300 to $3,800, both including air sealing and the blower-door readings. Dense-pack wall insulation is priced per square foot of wall and typically lands between $2.50 and $4.50. The scope, not the square footage alone, drives the number. Call (844) 320-7926 for a written price – the estimate is free and no work starts without it.
Yes. We install Owens Corning, Johns Manville, Knauf, and Rockwool materials, and we’ll recommend based on what your attic actually needs rather than what happens to be on the truck. Each brand behaves a little differently at depth, and we install to a measured, marked depth so the R-value on your documentation matches what’s in the attic. If you already have one of these brands installed, we can measure its current condition and top it up or replace it as the material allows.
Often, yes. We answer the phone 24/7 in Boulder City and can frequently get an assessment on the same day, especially for a top-up or a diagnostic visit. Full installations are usually scheduled within a day or two of the assessment. Call (844) 320-7926 and tell us the size of your attic if you know it, and we’ll tell you honestly what’s available today.
Every completed job is covered by the 365-Day Done Right Promise – if it’s not done right, we make it right. That’s backed by the written warranty you receive before anyone starts. You also get a Documented Photo Record of the sealing, the depth markers, and the finished attic, so there’s no dispute later about what was installed. If you have a competing estimate, we’ll read it with you for free and tell you what it does and doesn’t cover.
Clear the path to the attic access and move anything stored in the attic area the crew needs to reach. That’s usually the whole list. We handle sealing, the hose, the material, and the cleanup, and we’ll confirm the access point when we schedule. If you have pets or someone working from home, let us know and we’ll note it. You don’t need to do anything else ahead of time; we’d rather you call and ask than guess.
Schedule Your Blown-In Insulation Service in Boulder City Today
We’ll measure your attic, air seal it, blow insulation to a marked depth, and hand you the before-and-after blower-door numbers so you can see exactly what changed. Every job starts with a written price and ends with a documented record, backed by the 365-Day Done Right Promise. Call (844) 320-7926 for a free estimate – we answer 24/7, and we can often reach Boulder City the same day.
Written by the team at Envelope Insulation Co.