Icynene Insulation Removal & Replacement in Boulder City: What to Know First
Icynene insulation removal and replacement in Boulder City typically runs $2,200 to $7,800 depending on attic square footage, how much of the foam has to come out, and whether the old material has to be tested first. Most jobs take one to two days from setup to final walkthrough. We give you a written price before any work starts, and we publish before-and-after blower-door numbers so you can see what the removal and re-seal actually changed.
This page is for homeowners who already have Icynene in the attic, walls or rim joists and are weighing whether to pull it, patch it, or take the whole assembly out and start fresh. We service the Icynene family as an independent Icynene service provider, plus Reflectix and other products on the same job when the attic has a mix. If you want a number today, call us at (844) 320-7926.
How Icynene Products Fail – and How We Fix Them
What shows up in Boulder City attics often isn’t the foam failing on its own. It’s the surface under the foam that was never sealed, or the climate cycling that the install never accounted for. These are the failure modes we see most on Icynene jobs here.
- Icynene Classic (open-cell, older MD-R-200 era) sagging off roof decks. Open-cell foam that was sprayed too thin over warm decking can pull away as the desert heat drives moisture through the assembly. Once it separates, it stops being an air barrier and starts trapping dust behind the gap. Our fix is a clean removal of the loose sections, a moisture reading on the decking, then re-seal before any new product goes up.
- Icynene ProSeal (closed-cell) trapped against unsealed top plates. Closed-cell foam is a strong vapor and air barrier, so it hides what’s under it. When the crew sprayed it over top plates and can lights that were never air-sealed, the leaks don’t disappear, they just get sealed inside. The symptom is condensation on interior wallboard below the attic line. We pull the foam back at the plate line, air-seal the penetrations, and reset the barrier so the assembly actually works.
- Water staining on Icynene LD-R-50 in wall cavities. The low-density formula is more forgiving on flashing details than its siblings, but in Boulder City’s swing between cool nights and hot afternoons, it can wick moisture on south-facing wall cavities if the exterior WRB was lapped wrong. The staining shows up as a faint rust-brown bloom at the stud line. We open the cavity, document what we find, and replace with the manufacturer’s current spec plus a corrected WRB detail.
- Foam over a vermiculite layer that was never disclosed. Some Boulder City attics have an older mineral layer under the Icynene that nobody tested. We treat this as a contamination question, follow the test results, and pull the whole assembly if vermiculite is confirmed. Full contaminated-insulation removal, not a blower pass over the top.
- Off-spec Icynene from a stopped batch, or a foam job sprayed at the wrong temperature. Foam that sat too long or got sprayed outside the manufacturer’s temperature window cures off-ratio. It goes brittle, dusts at the touch, and stops holding the closed-cell ratio it was sold as. We pull it, replace with fresh material from the manufacturer’s current line, and re-test.
Our Icynene Insulation Removal & Replacement Process

- 1
Free second opinion on any written estimate you have. Bring us the quote. We’ll read it with you and flag anything that looks light on scope, like a removal line that skips the decking inspection or a replacement spec that doesn’t match what’s currently on your walls.
- 2
Written price, written scope, written warranty before any work starts. Under Haven Standard Clause 1, no crew lifts a tool until you have all three in your hand. Flat price, no day-of surprises.
- 3
Diagnostics: moisture readings, a blower-door test, and a visual on the decking. The blower door is a pressurization reading that shows, in one number, how much air your envelope is losing. We log the figure before removal so there’s a real baseline to compare against.
- 4
Removal. We pull the foam affected and any suspect layer beneath it. Foam is bagged and hauled off, and the decking gets cleaned before anything new goes up. No insulation goes back over an unsealed top plate or an unsealed can light.
- 5
Air sealing, then replacement. Top plates, can lights, and penetrations get sealed before any new product is sprayed or blown. The replacement foam comes from the current manufacturer line for whatever spec your assembly needs.
- 6
Re-test and close. Second blower-door reading, then a Documented Photo Record of the before, during, and after state. The 365-Day Done Right Promise backs the work; if something isn’t right, we make it right.
What Icynene Insulation Removal & Replacement Costs in Boulder City
Ranges below are what we see on real Boulder City jobs. Yours will land somewhere in these bands once we’ve seen the attic.
- Attic insulation removal (open-cell Icynene over a standard pitch): $1,800 to $3,900
- Contaminated insulation removal (vermiculite or water-stained layers): $3,200 to $6,800
- Closed-cell Icynene removal with decking re-seal: $2,600 to $5,400
- Replacement re-spray or blow-in after sealing: $1,400 to $3,200
- Air sealing at top plates, can lights and penetrations: $600 to $1,500
- Blower-door test (before and after, both readings logged): included on the job
What moves the price is really three things: how much foam has to come out, whether the decking needs re-seal or repair, and whether a lab test is needed for an older layer. Removal always costs more than a simple top-off, and that’s honest – pulling foam costs time and disposal and it’s the only way to fix a leak that’s sealed inside the assembly. Call (844) 320-7926 for a free estimate and a written price before anything starts.
Why Boulder City Homeowners Call Envelope Insulation Boulder City for Icynene Work

Icynene removal is a job you don’t want to learn on. Our technicians have up to 10 years of experience with spray foam and the Icynene family specifically, and they know which failure mode matches which symptom before they touch the attic. Every visit gets a Documented Photo Record, so the state of the assembly before and after lives in a file you keep – not in a memory of a conversation. Materials come from Owens Corning, Johns Manville, Knauf, Rockwool, CertainTeed, Icynene, Demilec and GreenFiber, so we’re not locked into a single product line if a different spec fits your assembly better.
If the attic also has a Reflectix radiant-barrier layer that’s been on top of failing foam, we handle both in one visit. We service Boulder City and the surrounding area, and a live person answers calls around the clock at (844) 320-7926.
Key Takeaways
- Icynene foam that’s sagged, off-ratio, or trapped over unsealed leaks has to come out, not get topped off.
- Every removal and replacement closes with before-and-after blower-door numbers you can see.
- Written price, written scope, written warranty before anyone lifts a tool.
- Free second opinion on any written estimate you already have.
FAQs
That depends on the original install and whether the foam is Icynene-branded, but on its own, the manufacturer’s warranty rarely covers removal and replacement driven by installation defects or leaks sealed inside the assembly. It almost never covers labor for the removal itself. We’ll read your existing paperwork with you at the free estimate and tell you honestly what your warranty likely does and doesn’t cover before you commit to anything. Call (844) 320-7926.
Usually, yes. Icynene’s current ProSeal and LD-R-50 lines are what most Boulder City homes get on replacement, and we match the spec to the assembly rather than pasting a like-for-like spray without checking the decking underneath. If your existing foam came from a discontinued line, we’ll walk through whether the current equivalent fits your cavity or whether a different product makes more sense. Free estimate on the whole scope.
In our experience, if the foam has sagged, gone off-ratio, or is trapping leaks it was supposed to seal, the honest call is usually full removal rather than patching. Small isolated sections – a single can light that got sprayed over – can sometimes be cut back and re-sealed without going full removal. We’ll tell you which case you’re in at the estimate, not on the invoice. Call (844) 320-7926 to get a written price.
Most Icynene removal and replacement jobs in Boulder City are scheduled within a week or two of the estimate, and most are completed in one to two working days from setup to walkthrough. Full contaminated-layer removals can run longer if test results are involved. If you’re on a tighter timeline, call (844) 320-7926 and we’ll tell you what we can actually do.
Yes, if there’s any reason to suspect an older mineral layer sitting under the Icynene, we test first and won’t touch the removal until results are back. Vermiculite in a Boulder City attic is a contamination question, not a product question, and it changes how the removal is scoped and priced. Free second opinion on any estimate you’re comparing.
Written by the team at Envelope Insulation Boulder City, serving Boulder City and nearby areas.