Demilec Attic Insulation: The Boulder City Owner’s Guide
We install Demilec-compatible attic insulation systems in Boulder City, and most whole-attic Demilec jobs here run between $2,400 and $6,800 installed, depending on square footage, existing insulation, and how much air sealing the attic floor needs first. Same-day service is often available for failed spray foam and settled injection foam when you call before mid-morning. Owners usually find the failure the same way: a heating bill that jumps $60 to $120 in one winter, a bare spot where foam pulled away from the roof deck, or a soft, crumbly patch above a can light that disintegrates when they touch it.
Before anything else, one fact worth stating plainly: Envelope Insulation Boulder City is an independent service provider and is not affiliated with Demilec. We install and repair Demilec-compatible systems, and we name the brand because the match matters to your home, not because of any partnership.
Key Takeaways
- Demilec attic foam in Boulder City usually fails at adhesion points and around penetrations before it fails across the field.
- Installed replacement typically lands between $2,400 and $6,800 for a whole attic.
- We always air seal before installing new insulation – blowing new product over an unsealed attic floor is a waste of money.
- You get a written price before any work starts and a Documented Photo Record when the crew leaves.
Which Demilec Models This Applies To
Demilec’s attic line centers on spray polyurethane foam and injection foam, and the part you’re actually replacing is usually one of a few things: the cured foam in a rafter bay, the injection foam in a wall cavity, or the foam at a penetration like a top plate or plumbing boot. The system name matters less than what’s written on the drum label and the SDS sheet the installer left behind. Look for the product name, the batch code, and the density spec – Demilec foam typically ships in open-cell or closed-cell formulations, and the two behave very differently against desert heat.
Here’s the compatibility gotcha most Boulder City owners run into: closed-cell Demilec foam can hit roughly 1.8 to 2.0 pounds per cubic foot, while open-cell lands near 0.5. If you’re patching, you need to match density to the surrounding foam or the patch looks and ages differently. Measuring is simple – a 1-inch slice of cured foam should weigh near 2 ounces closed-cell, near 0.5 ounces open-cell. When in doubt, we photograph the label and match it.
On the OEM versus aftermarket question: for Demilec foam specifically, we source through distributors that carry the Demilec line and equivalent products from Icynene, so you’re not locked into one brand if a batch or an exact spec is unavailable. That’s our model across every job. We also note when Reflectix radiant barrier is present in the same assembly, because foam over foil has to be installed differently.
Signs Your Demilec Attic Insulation Is Failing

Foam insulation fails locally before it fails globally – meaning the field of the foam usually holds while edges, penetrations, and seams open up. In Boulder City’s climate, with summer attic temps that regularly cross 140°F, that pattern shows up clearly if you know what to look for.
- Foam pulling away from the roof deck or rafters. That gap is a thermal bypass – heat moves through it freely. It usually means the surface was dusty or damp when applied, or the foam shrank as it cured in the heat.
- Crumbly or powdery patches. Cured foam should feel firm and slightly resilient. If it breaks into dust when you press it, the mix ratio was off or UV exposure degraded the outer skin.
- Bare spots above can lights and plumbing penetrations. These are the highest-risk areas because installers skip them or seal them poorly. If you can see bare drywall or a daylight gap, air is moving.
- A blower-door reading that hasn’t improved as promised. If the pre-work reading was, say, 4,200 CFM50 and the post-work read 3,900, something in the envelope isn’t sealed – often foam edges, not the foam itself.
- Condensation or staining on the attic floor near the foam. That points to warm moist air escaping through a gap beneath the foam, condensing on cool surfaces. In Boulder City’s dry climate, it’s usually a sign the air sealing underneath was skipped.
Replacement Cost & What’s Included
Most Demilec-compatible attic insulation replacement jobs in Boulder City land between $2,400 and $6,800 installed. The range comes down to three things: attic square footage, whether the existing foam needs removal or can be patched, and how much air sealing the attic floor requires before new product goes down.
| Line item | Typical range |
|---|---|
| Attic air sealing (top plates, penetrations, can lights) | $400 – $1,200 |
| Demilec-compatible spray foam – open-cell, installed | $1,800 – $4,200 |
| Demilec-compatible spray foam – closed-cell, installed | $2,400 – $5,500 |
| Existing foam removal (when required) | $300 – $900 |
| Blower-door test, before and after | Included |
Parts and labor are always quoted as one flat price in writing before any work starts. If the repair isn’t done right, the 365-Day Done Right Promise applies – we make it right.
DIY or Call Us?

You can safely check a few things yourself: look for foam pulling away from the deck, look for fine dust on the attic floor that suggests crumbling foam, and look for bare spots around can lights and plumbing. Photograph what you find and note the attic’s dimensions.
Where DIY goes wrong on Demilec foam: spray foam application requires correct temperature, moisture, and mix ratio, and getting any of those wrong produces a patch that looks fine and fails within a year. Foam applied over a dusty or damp surface delaminates. Foam applied over an unsealed attic floor traps moisture between the foam and the drywall. And removing existing foam without proper containment can distribute fine dust through the whole house. That’s why we always air seal first, then insulate, in that order.
Call us at (844) 320-7926 for a free estimate. We answer live, 24/7.
FAQs
Properly installed Demilec-compatible foam usually holds 20 to 30 years, but attic heat and UV exposure shorten that. In Boulder City’s 140°F-plus summer attics, foam that wasn’t applied to a clean, dry surface typically degrades at the edges within 8 to 12 years. Call (844) 320-7926 for an inspection – estimates are free.
Often yes. If the failure is local – a gap at a rafter, foam missing over a can light – we patch it rather than redo the whole attic. Typical patch jobs run $450 to $1,200. Call (844) 320-7926 and we’ll confirm whether patch or replace is the right call.
Most whole-attic Demilec-compatible replacements take one to two days, including air sealing and the blower-door test. Patch jobs usually finish same-day. Call (844) 320-7926 for a firm timeline.
We source Demilec-compatible foam through distributors that stock the Demilec line and equivalents from Icynene, so we match the density and formulation to what’s already in your attic. If a batch or spec is unavailable, we photograph the label and walk you through the equivalent before ordering.
Written by the team at Envelope Insulation Boulder City, serving Boulder City and nearby areas.
Every job begins with a written price before work starts and closes with a Documented Photo Record, including before-and-after blower-door readings on applicable jobs. Ready for a free estimate, or want a second opinion on an existing written quote? Call (844) 320-7926 – live person, 24/7.