Demilec Wall Insulation in Boulder City: What to Know First
We install Demilec injection foam and drill-and-fill wall insulation in Boulder City, and most single-wall jobs run one to two days from start to cleanup. Pricing is quoted in writing before any work starts, and it reflects the wall assembly we actually find, not a number we guessed over the phone. That written price, the scope, and the warranty all arrive before a tool comes off the truck.
This page is for owners of Demilec-foamed homes, and for buyers of older Boulder City houses who want to know what’s in the walls before they commit. Demilec wall systems have specific behaviors in the desert, and treating them like any other foam is how people end up paying twice.
Call (844) 320-7926 for a free estimate. A live person answers, any hour.
How Demilec Products Fail – and How We Fix Them
Demilec (now part of the Huntsman building solutions line, with Heatlok and SealTite among the names you’ll still see on spec sheets) makes a water-blown, low-density foam that does well in wall cavities when it cures correctly. In Boulder City’s heat and dryness, most of what we find in a failing Demilec wall isn’t a bad product. It’s a product installed into conditions it couldn’t tolerate.
- Shrinkage at the top plate on Heatlok-injected cavities. Low-density injected foam cures fast and pulls back slightly as it does. In a wall that wasn’t predrilled at the right spacing, the foam bridges and leaves a gap under the top plate, which reads as a draft at the ceiling line. We cut out the loose material, refill at the right pressure with a slower-cure mix, and air seal the plate before the wall goes back together.
- Cracking at stud faces in stud bays with high solar load. South and west walls in Boulder City get extreme cycling between a 110-degree afternoon and a 60-degree night. Low-density foam that was installed thin will hairline-crack along the studs after a few seasons. The fix is a top-up pass or a switch to a medium-density closed-cell Demilec product in those bays, not a patch smear.
- Off-ratio foam from a cold or wet day. If the foam was shot when the substrate was damp or the drums were cold, the A and B sides don’t react cleanly. You get a foam that’s crumbly, tacky, or faintly musty. This is a chemistry failure, not a coverage failure, and it has to be removed. We identify it by the texture and the smell, then cut it out and replace the cavity.
- Gaps at penetrations and box-outs. Plumbing stub-outs, electrical boxes, and window buck-outs in a Demilec wall are high-differential points where cured foam can pull away as the wood moves with the seasons. We re-seal each one with a compatible sealant and expanding fill, then verify with a blower-door reading.
- Hollow cavities in drill-and-fill retros. On a Demilec drill-and-fill application where the crew didn’t map the wall first, the foam can skip a cavity entirely or leave it half-full behind a stud. You find out from temperature difference across the wall or a cold spot. We scope the bays, reuse the injection holes where the pattern allows, and re-drill only where we have to.
This is the reason we insist on air sealing before insulation, every time. Blowing foam into an unsealed wall just traps the same leak behind a new layer.
Our Demilec Wall Insulation Process

Here’s what a Demilec wall job looks like, in order:
- 1
Free estimate and walk-through. We measure wall area, map the bays, and note the existing Demilec product and vintage. You get a flat written price, written scope, and written warranty before anything else happens.
- 2
Blower-door baseline. Before we open a single cavity, we run a blower-door test (a pressurization reading that shows, in one number, how much air your building envelope is losing). That number becomes the “before” you’ll compare against.
- 3
Diagnostics and removal. If existing Demilec foam is off-ratio or has failed, we cut it out and bag it. If it’s sound, we leave it and top up around it. We decide once we see it, and we tell you which it is.
- 4
Air seal, then insulate. Every penetration, top plate, and box-out gets sealed before the new foam goes in. This is a hard rule for us, not a step you can skip to save money.
- 5
Install and verify. We install the Demilec product the cavity calls for, then re-run the blower-door test. You get before-and-after CFM50 readings in writing.
- 6
Cleanup and documentation. Crew leaves with a documented photo record of every wall, penetration, and reading. Every job under the 365-Day Done Right Promise.
What Demilec Wall Insulation Costs in Boulder City
Here are honest, current ranges for Demilec wall work in Boulder City. Actual pricing depends on wall area, access, and whether old foam has to come out.
| Job | Typical range |
|---|---|
| Injection foam wall insulation, existing walls | $2.50 – $4.50 per sq ft of wall |
| Drill-and-fill from exterior | $1.80 – $3.20 per sq ft |
| Exterior wall insulation, new or open frame | $1.50 – $3.00 per sq ft |
| Interior wall soundproofing with Demilec | $1.20 – $2.40 per sq ft |
| Partial removal of failed foam | $300 – $900 per bay |
Wall area, access, existing foam condition, and whether you’re retrofitting an occupied home all move the price. We don’t work without a written price in hand, so your number is final before anyone lifts a tool.
Call (844) 320-7926 for your free estimate.
Why Boulder City Homeowners Call Envelope Insulation Boulder City for Demilec Work

We treat air sealing as a prerequisite, not an upsell. On every applicable job we run the blower-door test before and after and hand you the numbers. If a contractor tells you those figures don’t matter, ask them for theirs.
As an independent Demilec service provider, we’re not tied to one manufacturer. We source from Demilec, Icynene, Owens Corning, Johns Manville, and Rockwool, and we’ll also work alongside Reflectix products where a radiant barrier is already in the wall or roof assembly. You get the product the job needs, not the one we’re locked into.
Every Demilec job is backed by the 365-Day Done Right Promise. If something’s not right, we come back and fix it. Technicians are background-checked and uniformed, and our technicians have up to 10 years of experience. Calls are answered by a live person 24/7. No voicemail loops.
FAQs
Not if the work is done to the manufacturer’s spec and the foam is installed by a qualified crew. We follow Demilec’s published installation and curing requirements, and we document the install so your paperwork is intact. If you ever need to make a warranty claim, you’ll have the photos and readings to support it.
Common signs are a draft at the top plate, hairline cracks along studs on hot walls, or a musty smell behind drywall. If you’re seeing any of those, the foam is likely off-ratio or has separated. Call (844) 320-7926 for a free estimate and we’ll tell you what we find.
In most cases, yes. We carry access to the current Demilec and Huntsman building solutions line, and we can match the density and type in almost every Boulder City home we see. If a discontinued product is in there, we’ll tell you in the written scope and explain what we’re using instead.
Repair wins far more often than replacement. If the failure is a shrink gap, a crack pass, or a few hollow bays, we remove only the bad material, air-seal, and refill. Full removal only makes sense when the foam has gone off-ratio throughout. We’ll give you the honest call once we’ve opened the wall.
Most residential Demilec wall jobs run one to two days once we’re on site, though older homes with tricky access can stretch that. Scheduling is usually within the week. Call (844) 320-7926 for an exact date with your free estimate.
Written by the team at Envelope Insulation Boulder City, serving Boulder City and nearby areas.