Owens Corning Attic Insulation: The Boulder City Owner’s Guide
We install Owens Corning attic insulation products and compatible accessories for Boulder City homeowners. Most full attic insulation jobs here run $1,900 to $4,800 installed, depending on square footage, target R-value, and how much air sealing the attic floor needs first. On jobs that require removal of old material, expect to add $800 to $2,200. We can usually assess a Boulder City attic the same week you call, and we answer live 24/7.
Owners in Boulder City usually discover the problem the same way: a summer power bill that jumped $60 to $120 a month, a bedroom that won’t hold temperature past 3 p.m., or insulation that looks compressed or settled to half height when they climb up to check. Others find it after a rodent issue, a roof leak, or a home inspection flags thin coverage near the eaves.
Key takeaways: We’re an independent service provider, not affiliated with Owens Corning. Air sealing comes before any insulation goes down. You get a written price and a documented photo record on every job.
Which Owens Corning Models This Applies To
Owens Corning doesn’t sell “attic insulation models” the way it sells shingles with named series. What you’re matching is a product family to your attic’s needs. The main ones we install:
- AttiCat Expanding Blown-In Fiberglass (PINK fiberglass, blown): the most common choice for open, flat attic floors in Boulder City. Comes in bags rated by bag count per 1,000 sq ft to hit a target R-value.
- EcoTouch PINK FIBERGLAS batts: pre-cut blankets, R-13 through R-38, for kneewalls, sloped areas, and attics with tight framing where blowing is difficult.
- Thermafiber mineral wool: fire-resistant and non-combustible, useful near flues and chimneys.
- FOAMULAR rigid board: not a blown product, but relevant for cathedral ceilings and attic-to-rafter transitions.
To identify what’s already there, check the bag label stapled to a joist or the printed R-value on the facing of any batts. Measure settled depth with a tape in at least four spots. If the material is loose and pink, it’s almost certainly Owens Corning fiberglass or a compatible competitor.
On OEM versus aftermarket: for blown fiberglass, generic bags that meet the same R-value per inch honestly perform close to Owens Corning’s product. Where we don’t substitute is on accessories – baffles, vapor retarders, and air-sealing foam. Those are where cheap versions fail first. We source from Owens Corning, Johns Manville, Knauf, Rockwool, CertainTeed, and GreenFiber, with no proprietary product lock-in.
Signs Your Owens Corning Attic Insulation Is Failing

- Settled depth below label spec. Blown fiberglass loses roughly 15 to 25 percent of its installed depth over 10 to 15 years from vibration and gravity. That drop alone can cut your effective R-value by an R-5 to R-8.
- Compressed batts. Someone stepped on them, stored boxes on them, or HVAC ductwork was laid across them. Compression kills thermal performance instantly and doesn’t recover.
- Visible moisture staining or mildew smell. In Boulder City’s desert climate this usually points to a roof or plumbing leak, not humidity. Wet fiberglass loses R-value permanently and must be removed.
- Rodent tunneling and droppings. Fiberglass doesn’t stop rodents. Contaminated insulation has to come out, and entry points need sealing before new material goes in.
- Hot ceiling in summer, cold floor in winter. That’s your building envelope losing air. Before blaming the insulation, check whether top plates, can lights, and penetrations were ever air sealed. Blowing new insulation over unsealed gaps wastes the material.
Replacement Cost & What’s Included
Here’s what Boulder City homeowners actually pay:
| Scope | Typical installed range |
|---|---|
| Air sealing only (top plates, can lights, penetrations) | $650 – $1,400 |
| Blow-in fiberglass to R-49, existing attic, air sealed first | $1,900 – $3,400 |
| Blow-in to R-49 with batt removal and disposal | $2,700 – $4,800 |
| Baffles, vapor retarder, and code-required venting | $300 – $700 |
| Rodent proofing and contaminated removal | $800 – $2,200 |
What drives the range: square footage, current R-value versus target, accessibility (low-pitch roofs and tight attic hatches cost more labor), and whether old material has to come out. The price we write covers material, labor, disposal, and air sealing done first. We never blow insulation over an unsealed attic floor. Warranty on the work falls under our 365-Day Done Right Promise, and you walk away with before-and-after blower-door numbers showing how much air your home was losing.
DIY or Call Us?

You can safely do a few things yourself: measure settled depth with a tape, photograph the label on the bag, check for visible moisture or droppings, and look for gaps around pipes and can lights from the attic hatch without climbing in. Those facts help us quote accurately.
Where DIY goes wrong: blowing fiberglass over an unsealed attic floor. It’s the single most common mistake we see in Boulder City attics. Without air sealing at the top plates and penetrations, the new insulation sits over gaps that keep leaking conditioned air. A second problem is overfilling around can lights rated non-IC, which traps heat. And crawling through a low attic without proper lighting and a respirator is a real fall and respiratory risk. If your attic has fire-rated penetrations or complex ductwork, that’s a trained professional’s job.
Call (844) 320-7926 and we’ll give you a written price before any work starts, plus a free second opinion if you already have a written estimate from someone else.
FAQs
Fifteen to 25 years is realistic, with the practical limit usually tied to settling and air leaks rather than the product degrading. In Boulder City’s desert heat, attics routinely hit 140°F, which accelerates settling and any rodent or moisture damage. If yours is past 15 years, a blower-door test tells you whether it’s still doing its job.
Often yes. If your material is dry, uncontaminated, and covering evenly, we can top it up to target R-value and air seal underneath. Full removal only makes sense when there’s moisture, rodent contamination, or severe compression. A blower-door reading tells us which direction makes sense before we recommend either.
Most Boulder City attic insulation jobs are done in one day, typically four to six hours for a standard 1,500 sq ft attic. Jobs with removal or extensive air sealing run into a second day. You’ll get a written scope with an expected timeline before anyone lifts a tool.
We buy through regional distributors and match bag counts to your attic’s target R-value, then document what went in with photos and readings. We’re an independent service provider and not affiliated with Owens Corning, so we recommend the product that fits your attic, not the one on a sponsorship sheet. We also install Reflectix radiant barrier products where they make sense.
If your Boulder City attic is showing any of these signs, call (844) 320-7926 for a free estimate. You’ll get a written price before any work starts, a documented photo record of what we found, and before-and-after blower-door numbers so you can see exactly what the work accomplished.
Written by the team at Envelope Insulation Boulder City, serving Boulder City and nearby areas.